Stems

3TTT Mutant Black NOS/NIB Classic 130 mm 1" A-Head Stem

£40.00

✓ Original part - produced in the 1990s
✓ New old stock & still in the original packaging!
✓ Worldwide shipping

3TTT Mutant ahead handlebar stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 264 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

3TTT Mutant Black NOS/NIB Classic 130 mm 1" or 1 1/8" A-Head Stem

£40.00

✓ Original part - produced in the 1990s
✓ New old stock & still in the original packaging!
✓ Worldwide shipping

3TTT Mutant ahead handlebar stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 274 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

3TTT Mutant Silver NOS Classic 120 mm 1" A-Head Stem

£40.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

3TTT Mutant ahead handlebar stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 250 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

3TTT Mutant Silver NOS Classic 130 mm 1" A-Head Stem

£40.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

3TTT Mutant ahead handlebar stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 252 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

3TTT Mutant Silver NOS/NIB Classic 140 mm 1" A-Head Stem

£40.00

✓ Original part - produced in the 1990s
✓ New old stock & still in the original packaging!
✓ Worldwide shipping

3TTT Mutant ahead handlebar stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 259 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

3TTT Pinarello Branded NOS Classic 120 mm 1" Quill Stem

£45.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

3TTT stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from steel and weighing in at 369 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay (even with the new post-Brexit trade deals, some countries may charge you import VAT & clearance fees so please bear this in mind when purchasing).

3TTT Record Strada (Mod.1) 2nd Type Vintage 80 mm 1" Quill Stem

£35.00

✓ Original part - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & cleaned
✓ Worldwide shipping

3TTT Record Strada handlebar stem (or gooseneck if you prefer), hailing from Italy and in production during the 1970s. Made from aluminium and weighing in at 252 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

3TTT THE NOS/NIB Classic 120 mm 1" or 1 1/8" A-Head Stem

£35.00

✓ Original part - produced in the 2000s
✓ New old stock & still in the original packaging!
✓ Worldwide shipping

3TTT THE ahead handlebar stem, hailing from Italy and in production during the 2000s. Made from aluminium and weighing in at 222 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

Atax 1A Style Vintage 80 mm 1" Quill Stem

£40.00

✓ Original part - produced in the 1980s
✓ Lightweight for the era - just 275 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Atax stem, hailing from France and in production during the 1980s. Made from aluminium/steel and weighing in at 275 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc) - this is measured from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through. We always take this measurement in a straight line through middle of the extension, not along the top.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

ATAX P.R. 60 c.1983 Vintage 75 mm 1" French Quill Stem

£45.00

✓ Original part - produced in the 1980s
✓ Super lightweight for the era - only 222 grams!
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

ATAX P.R. 60 stem, hailing from France and dating back to 1983. Made from aluminium/steel and weighing in at 222 grams - incredibly lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc) - this is measured from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through. We always take this measurement in a straight line through middle of the extension, not along the top.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

AVA Vintage 75 mm 1" Quill Stem

£40.00

✓ Original part - produced in the 1970s
✓ Lightweight for the era - just 262 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

AVA stem, hailing from France and in production during the 1970s. Made from aluminium/steel and weighing in at 262 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc) - this is measured from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through. We always take this measurement in a straight line through middle of the extension, not along the top.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Avenir Classic 135 mm 1 1/8" Quill Stem

£45.00

✓ Original part - produced in the 1990s
✓ Professionally checked & cleaned
✓ Worldwide shipping

Avenir stem, hailing from the United States and in production during the 1990s. Made from steel and weighing in at 382 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc) - this is measured from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through. We always take this measurement in a straight line through middle of the extension, not along the top.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Belleri Forged NOS Vintage 60 mm 1" Quill Stem

£40.00

✓ Original part - produced in the 1970s
✓ New old stock! Still unused after all these years
✓ Lightweight for the era - just 283 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Belleri Forged stem, hailing from France and in production during the 1970s (yet still new & unused after all this time!). Made from aluminium and weighing in at 283 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay (even with the new post-Brexit trade deals, some countries may charge you import VAT & clearance fees so please bear this in mind when purchasing).

Cinelli Groove Black NOS Classic 100 mm 1" or 1 1/8" A-Head Stem

£45.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Cinelli Groove ahead handlebar stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 236 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

Cinelli Groove Silver NOS Classic 100 mm 1" or 1 1/8" A-Head Stem

£45.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Cinelli Groove ahead handlebar stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 233 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

Condition - New Old Stock*
Production Era - 1990s
Country - Italian
Material - Aluminium
Weight - 233 g
Stock Code - D-STA15C
NB - Includes shim reducer to fit 1" steerer

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Extension Length (ctc)* - 100 mm
Steerer Size (OD) - 1" or 1 1/8" (25.4mm / 28.6 mm)
Bar Clamp Size - 26.0 mm
Stack Height - 43 mm
Angle - 80 Degrees

*See help section.

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

 

 

 

 

 

Cinelli Groove Silver NOS Classic 110 mm 1" or 1 1/8" A-Head Stem

£45.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Cinelli Groove ahead handlebar stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 236 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

Claud Butler Cr-Mo Tube NOS Classic 120 mm 1 1/4" Quill Stem

£25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Claud Butler Cr-Mo Tube stem, hailing from Great Britain and in production during the 1990s (yet still new & unused after all this time!). Made from steel and weighing in at 440 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

GB Biba Vintage 100 mm 1" Quill Stem

£45.00

✓ Original part - produced in the 1980s
✓ Lightweight for the era - just 298 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

GB Biba stem, hailing from Great Britain and in production during the 1980s. Made from aluminium/steel and weighing in at 298 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc) - this is measured from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through. We always take this measurement in a straight line through middle of the extension, not along the top.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Italmanubri (ITM) 1A Style NOS Vintage 95 mm 1" Quill Stem

£45.00

✓ Original part - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Italmanubri (ITM) stem, hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from aluminium and weighing in at 329 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!

OVERVIEW

Condition - New Old Stock*
Production Era - 1970s & 1980s
Country - Italian
Material - Aluminium
Weight - 329 g
Stock Code - D-ST155V
NB - Marked as '90' extension but we measure 95 mm.

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Extension Length (ctc)* - 95 mm
Quill Size - 1"
Steerer Size (ID) - 22.2 mm (Standard)
Total Shaft Height - 160 mm
Clamp Size - 25.4 mm

*See help section.

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

 

 

 

 

 

ITM 400 T Bianchi Branded Vintage 90 mm 1" Quill Stem

£45.00

✓ Original part - produced in the 1980s
✓ Lightweight for the era - just 285 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

ITM 400 T stem, hailing from Italy and in production during the 1980s. Made from aluminium and weighing in at 285 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc) - this is measured from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through. We always take this measurement in a straight line through middle of the extension, not along the top.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

ITM Cromoly De Luxe NOS Classic 120 mm 1 1/8" Quill Stem

£30.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

ITM Cromoly De Luxe stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from steel and weighing in at 384 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay (even with the new post-Brexit trade deals, some countries may charge you import VAT & clearance fees so please bear this in mind when purchasing).

ITM Moray Black NOS/NIB Classic 120 mm 1" A-Head Stem

£40.00

✓ Original part - produced in the 1990s
✓ New old stock & still in the original packaging!
✓ Worldwide shipping

ITM Moray ahead handlebar stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 310 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

ITM NOS Vintage 95 mm 1" Quill Stem

£45.00

✓ Original part - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

ITM handlebar stem, hailing from Italy and in production from the 1970s to the 1980s (yet still new & unused after all this time). Made from aluminium and weighing in at 329 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Kalloy AL222 NOS Classic 70 mm 1" Quill Stem

£25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Kalloy AL222 handlebar stem (or gooseneck if you prefer), hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time). Made from aluminium and weighing in at 360 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Kalloy AL222 Silver NOS Classic 80 mm 1" Quill Stem

£25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Kalloy AL222 stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 385 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Kalloy KL60 Silver NOS Classic 60 mm 1" Quill Stem

£25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Lightweight for the era - just 287 grams
✓ Worldwide shipping

Kalloy KL60 stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 287 grams - pretty lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Kalloy Uno 7000 NOS Classic 130 mm 1" A-Head Stem

£35.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Kalloy Uno ahead handlebar stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 209 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

Kalloy Uno Black NOS Classic 130 mm 1 1/8" Quill Stem

£30.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 235 grams!
✓ Worldwide shipping

Kalloy Uno stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 235 grams - incredibly lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Kalloy Uno Silver NOS Classic 110 mm 1 1/8" Quill Stem

£25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 224 grams!
✓ Worldwide shipping

Kalloy Uno stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from auminium and weighing in at 224 grams - incredibly lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Kalloy Uno Silver NOS Classic 110 mm 1 1/8" Quill Stem

£25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 224 grams!
✓ Worldwide shipping

Kalloy Uno stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from auminium and weighing in at 224 grams - incredibly lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Kalloy Uno Silver NOS Classic 110 mm 1" Quill Stem

£25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 219 grams!
✓ Worldwide shipping

Kalloy Uno stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 219 grams - incredibly lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Kalloy Uno Silver NOS Classic 110 mm 1" Quill Stem

£27.50

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 219 grams!
✓ Worldwide shipping

Kalloy Uno stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 219 grams - incredibly lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Kalloy Uno Silver NOS Classic 130 mm 1 1/8" Quill Stem

£25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 237 grams!
✓ Worldwide shipping

Kalloy Uno stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 237 grams - incredibly lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Kalloy Uno Silver NOS Classic 130 mm 1 1/8" Quill Stem

£25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 237 grams!
✓ Worldwide shipping

Kalloy Uno stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 237 grams - incredibly lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Kalloy Uno Silver NOS Classic 130 mm 1" Quill Stem

£25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 230 grams!
✓ Worldwide shipping

Kalloy Uno stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 230 grams - incredibly lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Kalloy Uno Silver NOS Classic 150 mm 1 1/8" Quill Stem

£25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 247 grams!
✓ Worldwide shipping

Kalloy Uno stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 247 grams - incredibly lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Kalloy Uno Silver NOS Classic 90 mm 1 1/8" Quill Stem

£25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 216 grams!
✓ Worldwide shipping

Kalloy Uno stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 216 grams - incredibly lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Kalloy Uno Silver NOS Classic 90 mm 1" Quill Stem

£25.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Super lightweight for the era - only 209 grams!
✓ Worldwide shipping

Kalloy Uno stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 209 grams - incredibly lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Kore Lite Stem 3D Black NOS Classic 120 mm 1 1/8" A-Head Stem

£40.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Kore Lite Stem 3D ahead handlebar stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 239 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

Kore Lite Stem 3D Silver NOS Classic 120 mm 1 1/8" A-Head Stem

£40.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Kore Lite Stem 3D ahead handlebar stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 284 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

Kore Road NOS Classic 120 mm 1" or 1 1/8" A-Head Stem

£45.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Kore ahead handlebar stem, hailing from Taiwan and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 206 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

Modolo Q-Even NOS Vintage 130 mm 1" Quill Stem

£45.00

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Modolo Q-Even stem, hailing from Italy and in production during the 1980s (yet still new & unused after all this time!). Made from aluminium and weighing in at 375 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay (even with the new post-Brexit trade deals, some countries may charge you import VAT & clearance fees so please bear this in mind when purchasing).

Modolo Speedy Classic 95 mm 1" Quill Stem

£40.00

✓ Original part - produced in the 1990s
✓ Lightweight for the era - just 295 grams
✓ Professionally checked & cleaned
✓ Worldwide shipping

Modolo Speedy stem, hailing from Italy and in production during the 1990s. Made from aluminium and weighing in at 295 grams - pretty lightweight for a stem at that time. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike too.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc) - this is measured from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through. We always take this measurement in a straight line through middle of the extension, not along the top.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Raleigh Vintage 100 mm 1" Quill Stem

£30.00

✓ Original part - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping

Raleigh stem, hailing from Great Britain and in production from the 1970s to the 1980s. Made from aluminium/steel and weighing in at 348 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc) - this is measured from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through. We always take this measurement in a straight line through middle of the extension, not along the top.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Ritchey Comp Road NOS Classic 120 mm 1" A-Head Stem

£40.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Ritchey Comp ahead handlebar stem, hailing from the United States and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 197 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

Ritchey Pro Silver NOS Classic 130 mm 1 1/8" A-Head Stem

£35.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Ritchey Pro ahead handlebar stem, hailing from the United States and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 160 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

Ritchey Road Pro Black NOS Classic 120 mm 1" or 1 1/8" A-Head Stem

£40.00

✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Ritchey Road Pro ahead handlebar stem, hailing from the United States and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 185 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

Ritchey Road Pro Black NOS Classic 130 mm 1 1/8" A-Head Stem

£40.00

✓ Original part - produced in the 2000s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Ritchey Road Pro ahead handlebar stem, hailing from the United States and in production during the 2000s. Made from aluminium and weighing in at 156 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.

Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.

Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).

Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.

Sakae/Ringyo (SR) MTS-300 NOS Vintage 110 mm 1" Quill Stem

£35.00

✓ Original part - produced in the 1980s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping

Sakae/Ringyo (SR) MTS-300 stem, hailing from Japan and in production during the 1980s (yet still new & unused after all this time!). Made from aluminium/steel and weighing in at 374 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.

OVERVIEW

TECHNICAL INFO

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.

▼HELP SECTION

---

Extension Length (ctc)* - we measure from the centre of the handlebar clamp to the centre of the shaft, to the point where the stem bolt passes through, to the nearest 5 mm. We always take this measurement in a straight line through middle of the extension, not along the top. In some cases the stem may be stamped with a different extension length as some manufacturers measured differently, but we always use our own measurement for consitency.

Quill Size - the most common size for classic and vintage road bikes is 1", this should be the same as the outside diameter of your fork's steerer column. Oversized steerers found on mountain bikes and later road bikes will be either 1 1/8" or 1 1/4".

Steerer Size (ID) - this is the most important measurement when checking the stem fits your bike. This should match the measurement of the inside of your fork's steerer column, where the stem will be inserted. The standard size for road quill stems was 22.2 mm, or 22.0 mm in France until the 1980s.

Total Shaft Height - measured from the top where the expander bolt head sits, to the bottom of the stem's shaft. To give you an idea of how high the stem can be set, there should be an absolute minimum of 50 mm inserted into the fork steerer, although most stems come with a 'minimum insertion line' to help with this.

Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.

Sakae/Ringyo (SR) NOS Vintage 60 mm 1" Quill Stem

£45.00

✓ Original part - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Lightweight for the era - just 286 grams
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping

Sakae/Ringyo (SR) stem, hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time!). Made from aluminium and weighing in at 286 grams - pretty lightweight for a stem at that time. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.

If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong stem!

OVERVIEW

Condition - New Old Stock*
Production Era - 1970s & 1980s
Country - Japanese
Material - Aluminium
Weight - 286 g
Stock Code - D-ST46V

*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.

TECHNICAL INFO

Extension Length - 60 mm
Quill Size - 1"
Steerer Size (ID) - 22.2 mm (Standard)
Shaft Height - 150 mm
Clamp Size - 26.0 mm

▼SHIPPING, TAXES & RETURNS

---

We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 working days but larger items can often take a little longer to process.

We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.

We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay (even with the new post-Brexit trade deals, some countries may charge you import VAT & clearance fees so please bear this in mind when purchasing).