Recently Added
Suntour Vintage 10T Jockey Wheels
£20.00
✓ Original jockey wheels - in production from the 1970s to the 1980s
✓ Checked & cleaned
✓ Worldwide shipping
Suntour jockey wheels (or derailleur pulleys if you prefer), hailing from Japan and in production from the 1970s to the 1980s. Made from plastic and weighing in at 22 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
The jockey wheels have been thoroughly checked & cleaned and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Production Era - 1970s & 1980s
Country - Japanese
Material - Plastic
Weight - 22 g
Stock Code - U-JCK8V
TECHNICAL INFO
Teeth - 10
Compatible Speed* - 5 Speed, 6 Speed, 7 Speed
Diameter (OD) - 38 mm
Thickness - 10.2 mm
Centre Hole (ID) - 6.1 mm
*See help section.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Teeth - the tooth count has increased with the introduction of more gears, but this happened very gradually so 10 tooth jockey wheels were standard for a very long time.
*Compatible Speed - the number of cogs the jockey wheels were designed to be used with. When using derailleurs for indexed shifting it's important to stick to this, but friction shifting is much more forgiving so you're unlikely to have any problems using the next speed up or down, providing all the measurements are correct.
Diameter (OD) - the diameter of the jockey wheels, from the outside edge of the teeth. It’s important to stay close to the ones you're replacing to ensure they fit.
Thickness - measured at the widest point, by the centre hole. The spacing has generally become narrower over the years to accommodate more gears.
Centre Hole (ID) - the inside diameter (usually inside the bushing/spacer if present). This rarely presents a problem, but some older jockey wheels have a different diameter so it's worth double checking.
Suntour Superbe 68-W Vintage 114 mm Bottom Bracket Axle
£35.00
✓ Original part - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & cleaned
✓ Worldwide shipping
Suntour Superbe bottom bracket axle (or BB spindle if you prefer), hailing from Japan and in production from the 1970s to the 1980s. Made from steel and weighing in at 149 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong axle!
The axle has been thoroughly checked, cleaned and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Production Era - 1970s & 1980s
Country - Japanese
Material - Steel
Weight - 149 g
Stock Code - U-BB-AS13V
TECHNICAL INFO
Axle Type - Square Taper
Axle Markings - 68-W
Axle Length (D) - 114 mm
Axle Centre (B) - 50.5 mm
Axle Drive Side (C) - 34 mm
Axle Non-Drive Side (A) - 29.5 mm
Shell Width - 68 mm
NB: Check the help section to see how we take these measurements.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
- We've provided reference below to illustrate how we take the measurements.
Axle Type - for square tapers, the ISO introduced a standard for European makers in the early 90s, JIS then did the same in Asia. Before then it was not so simple, and although there is a degree of interchangeability, the best way to make sure you have the right axle is to stick to the same brand from the same era, ideally the proprietary model.
Axle Length (D) - your crankset dictates the axle length you need and the recommendation should be used to avoid issues with chainline. If you're replacing an axle that works perfectly then this can be matched, otherwise you'll need to check the manufacturers spec, a good resource for older bikes is Velobase.
Centre (B) - measured from the outside of the 'shoulders' of the bearing races, as seen in the diagram.
Drive Side (C) - the right side (with any logos etc on the axle facing you), your right crank and chainrings will mount to this side.
Non-Drive Side (A) - the left side, where the left crank arm will be mounted.
Shell Width - the width of the bottom bracket shell the axle was designed to fit, measured at its widest point.
Suntour XC / XCD Hardliner NOS Vintage Black MTB Brake Cable Set
£35.00
✓ Original parts - in production from the 1980s to the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping
Suntour XC / XCD cable set (outer casing and inner wires), hailing from Japan and in production from the 1980s to the 1990s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
OVERVIEW
Production Era - 1980s & 1990s
Country - Japanese
Stock Code - D-CAB-S13V
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Position - Front & Rear
Bike Suitability - MTB
Cable Type - Brake
Colour* - Black
Casing Width (OD) - 5 mm
Wire Diameter - 1.8 mm
Casing Length - 57 cm / 117 cm
Inner Length - 68 cm / 128 cm
Brake End Nipple Type - Barrel
End Nipple Diameter - 7 mm (8 mm With Brass Cover)
Barrell End Thickness - 8 mm
*The colour description is just a guide, please check the photos too as we make sure these are as close to the true colour as possible.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Position - rear cables need to be longer than fronts, this is the only difference so cables long enough for the rear can also be used on the front.
Cable Type - brake and gear cables have different specifications and are not interchangeable.
Casing Width - the outside diameter of the housing. Brake cable housing is a little wider in diameter than gear, this is to accommodate the slightly thicker inner cables.
Length - it's important to check the cables are long enough for your setup. Some gear cables are designed for downtube gear levers only and there won't be enough cable to be used otherwise.
Brake End Nipple Type - Pear' type cable ends step down in size to allow them to be used with drop bar brake levers normally found on road bikes, whereas flat bar levers usually require a 'barrel' end that sits in a similar shape slot within the brake levers.
End Nipple Diameter - for 'pear' type ends this is the diameter at its widest part, with barrel ends it's the diameter of the circular part.
Suntour GPX / Radius (FW-AL10-S6R) Accushift Plus c.1990 Vintage 6 Speed 13-18 Freewheel
£45.00
✓ Original part - in production from the 1980s to the 1990s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & carefully cleaned
✓ Worldwide shipping
Suntour GPX / Radius freewheel, hailing from Japan and dating back to 1990. Made from steel and weighing in at 335 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong freewheel!
The freewheel's been carefully cleaned, thoroughly checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy, and please consider that freewheels wear with chains, so used freewheels can occasionally skip when partnered with new (and some used) chains. This can usually be avoided by using a compatible used chain of similar age, but there is no way for us to confirm which chain will work with which freewheel.OVERVIEW
Model ID - FW-AL10-S6R
Production Era - 1980s & 1990s
Country - Japanese
Material - Steel
Weight - 335 g
Stock Code - U-FW191V
TECHNICAL INFO
Speed (No of Cogs) - 6 Speed
Range - 13-18
Threading - English/ISO: 1.375 x 24 TPI
Stack Height - 31 mm
Cog Width - 3/32" (Standard)
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Speed - the number of cogs on the freewheel.
Range - the number of teeth on the smalles and largest cogs, this gives you an indication of how hard or easy the gearing will be, the lower the number the harder the gears. The tooth count of the cogs inbetween are usually evenly spaced, ie: a 6 speed 14-24 freewheel would likely have cog sizes 14, 16, 18, 20, 22 & 24.
Threading - this needs to match the thread of your rear hub. ISO is the modern standard and is almost exactly the same as older English/British and Italian thread, allowing you to mix and match between these thread types as long as it's not going to be under extreme force, in which case it's best to stick to an exact match. Hubs with a French thread must be used with a French threaded freewheel.
Stack Height - the total height (or width if you're looking at it when installed) of the freewheel, this is measured from the base (back of the largest cog) to the top (front of the smallest cog).
Cog width - this is mainly relevant for singlespeed and some older 3 or 4 speed freewheels - if this is ⅛” then you must use a ⅛” chain, but most freewheels (especially multiple speed ones) will use a standard 3/32” chain.
Suntour New Winner (NW-7000) Vintage 7 Speed 12-18 Freewheel
£55.00
✓ Original part - produced in the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Professionally checked & carefully cleaned
✓ Worldwide shipping
Suntour New Winner freewheel, hailing from Japan and in production during the 1980s. Made from steel and weighing in at 366 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong freewheel!
The freewheel's been carefully cleaned, thoroughly checked by one of our mechanics and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy, and please consider that freewheels wear with chains, so used freewheels can occasionally skip when partnered with new (and some used) chains. This can usually be avoided by using a compatible used chain of similar age, but there is no way for us to confirm which chain will work with which freewheel.OVERVIEW
Model ID - NW-7000
Production Era - 1980s
Country - Japanese
Material - Steel
Weight - 366 g
Stock Code - U-FW193V
TECHNICAL INFO
Speed (No of Cogs) - 7 Speed
Range - 12-18
Threading - English/ISO: 1.375 x 24 TPI
Stack Height - 35.5 mm
Cog Width - 3/32" (Standard)
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Speed - the number of cogs on the freewheel.
Range - the number of teeth on the smalles and largest cogs, this gives you an indication of how hard or easy the gearing will be, the lower the number the harder the gears. The tooth count of the cogs inbetween are usually evenly spaced, ie: a 6 speed 14-24 freewheel would likely have cog sizes 14, 16, 18, 20, 22 & 24.
Threading - this needs to match the thread of your rear hub. ISO is the modern standard and is almost exactly the same as older English/British and Italian thread, allowing you to mix and match between these thread types as long as it's not going to be under extreme force, in which case it's best to stick to an exact match. Hubs with a French thread must be used with a French threaded freewheel.
Stack Height - the total height (or width if you're looking at it when installed) of the freewheel, this is measured from the base (back of the largest cog) to the top (front of the smallest cog).
Cog width - this is mainly relevant for singlespeed and some older 3 or 4 speed freewheels - if this is ⅛” then you must use a ⅛” chain, but most freewheels (especially multiple speed ones) will use a standard 3/32” chain.
Suntour XC Sport 7000 (FD-XS00-GX) c.1987 Vintage Clamp-On 28.6 mm Front Derailleur
£35.00
✓ Original part - produced in the 1980s
✓ Professionally checked & cleaned
✓ Worldwide shipping
Suntour XC Sport 7000 front derailleur (or mech, or changer if you prefer), hailing from Japan and dating back to 1987. Made from aluminium/steel and weighing in at 113 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
The derailleur's been carefully cleaned, thoroughly checked by one of our mechanics" and graded as good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Model ID - FD-XS00-GX
Production Era - 1980s
Country - Japanese
Material - Aluminium / Steel
Weight - 113 g
Stock Code - U-FM196V
TECHNICAL INFO
Chainset Type - Triple
Frame Fixing - Clamp-On 28.6 mm
Pull Type - Bottom Pull
*See help section.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Chainset Type - the number of chainrings the derailleur was designed to work with. ‘Double’ derailleurs are actually capable of working on ‘triple’ chainsets but they may struggle when shifting, especially if there’s a big step down from the middle to inner ring, so it’s better to match these correctly.
Frame Fixing - the way the derailleur fixes to the frame, if you have a tab on your frame to mount the derailleur to you need braze-on. If there’s no tab then you require a clamp-on type (also referred to as band-on or clip-on), these come in different sizes to match the diameter of your seat tube.
Pull Type - the direction of which the cable needs to ‘pull’ the mech in order to shift. If your cable runs up to the derailleur from the bottom bracket area then you need bottom pull, if your cable comes down from above you need top pull. Some later derailleurs can be used for either setups, these are referred to as dual pull.
Designated Speed (9 Speed & Above) - the speed of the chain that the mech was designed to be used with. This only becomes relevant for mechs marketed as 9 speed or above when chains became narrower, as the derailleur cage plates became marginally narrower too. We refer to it as ‘designated’ speed as technically you can use (almost) any derailleur with any chain, however if you want optimum performance it’s best to stay close to the manufacturers recommendations.
Indexing System (Shimano Only) - this is only applicable when using Shimano shifters that have an indexed left shifter such as STI or Rapidfire. For the indexing to work correctly when using these shifters the derailleur and shifters must be of the same type, so Shimano drop bar shifters need to be matched with a Shimano ‘road’ derailleur, and Shimano flat bar shifters must be used with Shimano ‘MTB’ derailleurs.
Suntour Superbe / Cyclone Vintage Steel Derailleur Gear Cable Housing
£30.00
✓ Original cable housing - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & photographed in detail
✓ Worldwide shipping
Suntour Superbe / Cyclone cable housing (or outer casing if you prefer), hailing from Japan and in production from the 1970s to the 1980s. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable!
The housing has been checked over and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Production Era - 1970s & 1980s
Country - Japanese
Stock Code - U-CAB-O7V
TECHNICAL INFO
Length - 24 / 16.5 cm
Colour* - Steel (Stainless)
Housing Type - Gear Shifter - Derailleur (Front & Rear Mech)
Casing Width (OD) - 4.3 mm
Ferrule Size (OD) - 5.8 mm
*The colour description is just a guide, please check the photos too as we make sure these are as close to the true colour as possible.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Housing Type - brake and gear cables have different specifications and are generally not interchangeable, although older bikes with non-index shifting often used brake housing instead of gear. We'd still recommend using the dedicated front or rear derailleur cable housings for non-index setups whenever possible.
Casing Width - the outside diameter of the housing. Brake cable housing is a little wider in diameter than gear, this is to accommodate the slightly thicker inner cables.
Ferrule Size - if ferrules are included, this measurement is of the outside diameter at the widest part
Suntour Superbe / Cyclone Vintage Steel Derailleur Gear Cable Housing
£35.00
✓ Original cable housing - in production from the 1970s to the 1980s
✓ Suitable for historic cycling events such as L'Eroica
✓ Checked & photographed in detail
✓ Worldwide shipping
Suntour Superbe / Cyclone cable housing (or outer casing if you prefer), hailing from Japan and in production from the 1970s to the 1980s. The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or any other vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cable!
The housing has been checked over and graded as very good condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Production Era - 1970s & 1980s
Country - Japanese
Stock Code - U-CAB-O6V
TECHNICAL INFO
Length - 27.5 / 17 cm
Colour* - Steel (Stainless)
Housing Type - Gear Shifter - Derailleur (Front & Rear Mech)
Casing Width (OD) - 4.3 mm
Ferrule Size (OD) - 5.8 mm
*The colour description is just a guide, please check the photos too as we make sure these are as close to the true colour as possible.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Housing Type - brake and gear cables have different specifications and are generally not interchangeable, although older bikes with non-index shifting often used brake housing instead of gear. We'd still recommend using the dedicated front or rear derailleur cable housings for non-index setups whenever possible.
Casing Width - the outside diameter of the housing. Brake cable housing is a little wider in diameter than gear, this is to accommodate the slightly thicker inner cables.
Ferrule Size - if ferrules are included, this measurement is of the outside diameter at the widest part
Suntour NOS Vintage Road Gear Shifter Cable Inners
£20.00
✓ Original cables - in production from the 1970s to the 1980s
✓ New old stock! Still unused after all these years
✓ Suitable for historic cycling events such as L'Eroica
✓ Worldwide shipping
Suntour set of 2 inner cables (or wires if you prefer), hailing from Japan and in production from the 1970s to the 1980s (yet still new & unused after all this time). The perfect finishing touch for your vintage bike, but great for bikes of the non-vintage variety too!
If you're taking part in L'Eroica or any other vintage event, these are fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong cables!
OVERVIEW
Production Era - 1970s & 1980s
Country - Japanese
Stock Code - D-CAB-P5V
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Bike Suitability - Road (Downtube Shifters)
Cable Type - Gear Shifter (Derailleur)
Length (F/R) - 80 cm / 130 cm
Wire Diameter - 1.5 mm
End Diameter - 4.5 mm
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Cable Type - brake and gear cables have different specifications and are not interchangeable.
Length (F/R) - it's important to check the cables are long enough for your setup. Some gear cables are designed for downtube gear levers only and there won't be enough cable to be used otherwise.
End Nipple Type - only relevant for brake cables. 'Pear' type cable ends step down in size to allow them to be used with drop bar levers normally found on road bikes, whereas flat bar levers usually require a 'barrel' end that sits in a similar shape slot within the brake levers.
End Diameter - for 'pear' type ends this is the diameter at its widest part, with barrel ends it's the diameter of the circular part.
Suntour XCD (BL-XD10-S) Multi Mount NOS Vintage MTB Brake Levers
£85.00
✓ Original levers - in production from the 1980s to the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping
Suntour XCD flat bar brake levers (or handles if you prefer), hailing from Japan and in production from the 1980s to the 1990s (yet still new & unused after all this time!). Made from aluminium/rubber and weighing in at 222 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
OVERVIEW
Model ID - BL-XD10-S
Production Era - 1980s & 1990s
Country - Japanese
Material - Aluminium / Rubber
Weight - 222 g
Stock Code - D-LEV-F11V
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Bike Type - MTB
Brake Type - Cantilevers
Bar Clamp Size - 22.2 mm
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Bike Type - this is just a guide, any brake levers can technically be used on any bike as long as everything's compatible.
Brake Type - if you’re running direct pull cantilevers (V-Brakes), you’ll need compatible brake levers. For calipers, cantilevers and mini V-brakes you’ll need levers designed to be used with these as the cable pull is different.
Bar Clamp Size - this should be close to the outside diameter of your handlebars at the point the brake levers will be fitted. 23.8 mm is standard for drop bars and 22.2 mm is standard for 'flat' bars (including risers & swept-back types), but they can differ so this should be checked.