£25 to £50
Cinelli Criterium (65) Winged C Logo Vintage 40 cm Drop Handlebars
£35.00
✓ Original bars - in production from the 1980s to the 1990s
✓ Checked, cleaned & tape residue removed
Cinelli Criterium drop handlebars, hailing from Italy and in production from the 1980s to the 1990s. Made from aluminium and weighing in at 325 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike.
The bars have been checked, handlebar tape residue removed and graded as OK condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Model ID - 65
Production Era - 1980s & 1990s
Country - Italian
Material - Aluminium
Weight - 325 g
Stock Code - U-HB196V
TECHNICAL INFO
Width (ctc)* - 40 cm
Shape - Classic
Clamp Size - 26.4 mm
Drop (ctc) - 148 mm
Reach (ctc) - 75 mm
Cable Groove - None
*See help section.
Width (ctc)* - measured at the ends of the drops, from the centre of one side to the other (ctc), to the nearest cm. In some cases the bars may display a different width as some brands measure outside to outside rather than ctc, but we always use this measurement for consistency.
Shape - Classic' drops have a smooth curve, 'anatomic' have multiple angles for different hand positions, 'compact' are short reach with a shallow drop and randonneur bars are usually classic in shape but rise up then flare out at the drops.
Clamp Size - this should match the internal diameter of your handlebar stem clamp, and should be as close as possible to ensure a good and safe fit.
Drop (ctc) - from the top flat section to the bottom of the drops, measured from the centre of one to the other with the flat part at the end of the drops parrallel to the ground.
Reach (ctc) - measured from the centre of the top section to the centre of the 'curve' at its furthest point, giving you the maximum reach. We measure this with the flat part at the end of of the drops parrallel to the ground.
Cable Groove - these allow you to run your cables neatly underneath the handlebar tape, if your setup requires this.
Cinelli Groove Black NOS Classic 100 mm 1" or 1 1/8" A-Head Stem
£45.00
✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping
Cinelli Groove ahead handlebar stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 236 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
Production Era - 1990s
Country - Italian
Material - Aluminium
Weight - 236 g
Stock Code - D-STA13C
NB - Includes shim reducer to fit 1" steerer
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Extension Length (ctc)* - 100 mm
Steerer Size (OD) - 1" or 1 1/8" (25.4mm / 28.6 mm)
Bar Clamp Size - 26.0 mm
Stack Height - 43 mm
Angle - 80 Degrees
*See help section.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.
Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.
Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).
Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.
Cinelli Groove Silver NOS Classic 100 mm 1" or 1 1/8" A-Head Stem
£45.00
✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping
Cinelli Groove ahead handlebar stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 233 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
Condition - New Old Stock*
Production Era - 1990s
Country - Italian
Material - Aluminium
Weight - 233 g
Stock Code - D-STA15C
NB - Includes shim reducer to fit 1" steerer
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Extension Length (ctc)* - 100 mm
Steerer Size (OD) - 1" or 1 1/8" (25.4mm / 28.6 mm)
Bar Clamp Size - 26.0 mm
Stack Height - 43 mm
Angle - 80 Degrees
*See help section.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.
Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.
Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).
Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.
Cinelli Groove Silver NOS Classic 110 mm 1" or 1 1/8" A-Head Stem
£45.00
✓ Original part - produced in the 1990s
✓ New old stock! Still unused after all these years
✓ Worldwide shipping
Cinelli Groove ahead handlebar stem, hailing from Italy and in production during the 1990s (yet still new & unused after all this time!). Made from aluminium and weighing in at 236 grams. A fine choice for keeping your classic bike authentic, but also great for any other compatible bike.
OVERVIEW
Production Era - 1990s
Country - Italian
Material - Aluminium
Weight - 236 g
Stock Code - D-STA14C
NB - Includes shim reducer to fit 1" steerer
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Extension Length (ctc)* - 110 mm
Steerer Size (OD) - 1" or 1 1/8" (25.4mm / 28.6 mm)
Bar Clamp Size - 26.0 mm
Stack Height - 43 mm
Angle - 80 Degrees
*See help section.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.
-
▼HELP SECTION
-
Extension Length (ctc)* - measured from the centre of the handlebar clamp to the centre of the steerer clamp, to the nearest 5 mm. This measurement is taken through the middle of the extension, not along the top or bottom.
Steerer Size (OD) - OD means outside diameter, this is the most important measurement when checking the stem fits your bike. This should match the measurement of the outside of your fork's steerer column, where the stem will be clamped.
Bar Clamp Size - this should match the outside diameter of your handlebars and should be as close as possible to ensure a good and safe fit.
Stack Height - the height of the part that clamps to the forks. This is the minimum amount of space you will need on the fork's steerer column for the stem to fit (minus a few mm as the top of the steerer tube needs to sit just below the top of the stem).
Angle - the angle of the stem's extension in relation to the the fork steerer. Bear in mind the steerer sits at the same angle as the head tube, so a 90 degree stem would not be parallel to the ground. Some manufacturers refer to this as rise or drop, in which case an 80 degree stem would drop 10 degrees from a right angle. Most a-head stems can be flipped although it does depend on the design.
Cinelli Ribbon NOS/NIB Classic Blue/Red Cork Handlebar Tape
£25.00
✓ Original bar tape - produced in the 1990s
✓ New old stock & still in the original packaging!
Cinelli Ribbon bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1990s (yet still new & unused after all this time). The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
Production Era - 1990s
Country - Italian
Stock Code - D-BT98C
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Colour* - Blue / Red
Tape Style - Cork
*The colour description is just a guide, please check the photos too as we make sure these are as close to the true colour as possible.
View full product details
Cinelli Ribbon NOS/NIB Classic Yellow/Red/Blue Cork Handlebar Tape
£25.00
✓ Original bar tape - produced in the 1990s
✓ New old stock & still in the original packaging!
Cinelli Ribbon bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1990s (yet still new & unused after all this time). The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
Production Era - 1990s
Country - Italian
Stock Code - D-BT99C
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Colour* - Yellow / Red / Blue
Tape Style - Cork
*The colour description is just a guide, please check the photos too as we make sure these are as close to the true colour as possible.
View full product details
Cinelli Ribbon Splash NOS/NIB Classic Yellow/Blue Cork Handlebar Tape
£25.00
✓ Original bar tape - produced in the 1990s
✓ New old stock & still in the original packaging!
Cinelli Ribbon bar tape (or grip, or wrap if you prefer), hailing from Italy and in production during the 1990s (yet still new & unused after all this time). The perfect finishing touch for your classic bike, but great for bikes of the non-classic variety too!
OVERVIEW
Production Era - 1990s
Country - Italian
Stock Code - D-BT100C
*New old stock items may have marks from storage over the years, and as we often have multiples they can vary from piece to piece, but they are always genuine new & unused items.
TECHNICAL INFO
Colour* - Yellow / Blue
Tape Style - Cork
*The colour description is just a guide, please check the photos too as we make sure these are as close to the true colour as possible.
View full product details
Cinelli Unicanitor (Mod. 75 #3) Vintage Brown/Red Leather Saddle
£35.00
✓ Original saddle - produced in the 1970s
✓ Suitable for historic cycling events such as L'Eroica
✓ Thoroughly checked & photographed in detail
✓ Worldwide shipping
Cinelli Unicanitor saddle, hailing from Italy and in production during the 1970s. Made from leather/steel and weighing in at 437 grams. A fine choice for keeping your vintage bike authentic, but also great for any other compatible bike too.
If you're taking part in L'Eroica or a similar vintage event, this is fully compliant - so rest assured, the pre-1987 police won't lock you up for having the wrong saddle!
The saddle's been checked over and graded as poor condition, but do take a good look at the detailed photos so you can see the cosmetic condition before you buy.OVERVIEW
Model ID - Mod. 75 #3
Production Era - 1970s
Country - Italian
Material - Leather/Steel
Weight - 437 g
Stock Code - U-SA31V
TECHNICAL INFO
Colour* - Brown/Red
Cover Material - Leather
Length - 280 mm
Width - 145 mm
*The colour description is just a guide, please check the photos to get a good idea of the colour too, as we make sure these are as close to the true colour as possible.
-
▼SHIPPING, TAXES & RETURNS
-
We've been safely sending orders around the world since 2010. There's a handy shipping calculator on the shopping cart page so you can see the cost of postage as soon as you've added it to your basket. Your order will be carefully packed and sent with tracking & insurance, we despatch most orders within 2-3 days but larger items and orders placed before the weekend can take an extra day or two to process.
We accept returns, please notify us within 14 days and ensure the item arrives back with us no later than 30 days after the order was received.
We don't charge VAT, however, if buying from outside of the UK please remember that there may be import fees to pay directly to the delivery company before receiving the order. Unfortunately we can’t advise on the exact costs as it varies from country to country, so please check your national rates before purchasing.